I completely removed all four leads from the PSU that had 4-Pin Molex and SATA power connectors and replaced them with only two leads made from the G5's stock black wiring with two SATA power connectors very close together on one lead for the hard drives and the second lead having only one SATA and one 4-pin molex for the Optical drive and fans when I get to that point. I also had my fair share of soldering today. And best of all the I/O shield snaps in and out like it should, so swapping boards will be no problem. I finally got around to getting the rear I/O inset piece installed and I'm pleased to say everything lines up. I need to trim it a little more though.Īnd a few minutes ago I cut a 4.5" hole in the bottom of the stock G5 power supply case for the PSU cooling fan as well as block off the holes where the two 60mm fans were located with a piece of cut aluminum.Īnd as for the corresponding hole cut into the bottom of the G5 case, VOILA! Here is a pic of its location being mocked up. So now that I've got the tray installed properly, right now I'm getting ready to cut the rear of the case and fit the aluminum inset piece which will hold the motherboards I/O shield. Power mac g5 conversion kit plus#One of the main concerns was that I didn't want to completely butcher the case plus I really like some of the high end mATX boards soon to be released like the Asus Z87 Gryphon seen here: To make sure everything was lined up while the epoxy set, i mounted a shortened mATX board that I had been using in a media server so when I decide on a proper mATX board, it should be a few inches longer. some light sanding and a shot of satin clear coat, this is the result:Ī healthy dose of 2 part epoxy and the tray is definitely not going anywhere. It came out of a Coolermaster Stacker case.Īnd after removing some rivets, and some slicing and dicing with my angle grinder equipped with a cut-off blade. Power mac g5 conversion kit full#So far I've gutted the G5, removed all the stand-offs, and began work on the PSU and Motherboard tray.įor a motherboard tray, I looked around online at Lian-Li and MountainMods but after some consideration, I realized I had a full aluminum tray collecting dust in my garage which I saved years ago for a project just like this. I'll have pics of that tonight once I get some time. I plan on using an mATX motherboard so I can also keep the power supply where it belongs, but I'm already in the process of changing out the guts of the PSU with a 600w OCZ I had laying around. I haven't completely decided on the guts but I know I'm going to configure it to retain the rear expansion slots but remove the I/O ports. So I've built a few Hackintosh systems in the past but never the actual case even though I've been modding PCs since AMD released the first Athlon in 1999. it was deduced that the logic board was shot and in addition to payment for the work, he gave me the computer to do as i see fit. last week a relative called me and asked if i'd come down to his office to diagnose why his backup graphic design PowerMac G5 dual 1.8 (June 2004) was not booting and after some frustration with the common "3 blinks" memory error, trying other good ram, and many other things. Power mac g5 conversion kit pro#Mac Pro ATX kit with PSU mount The rear of the Pro kit fits as shown above to allow a full ATX board to go into the Mac Pro casing.For many years I've wanted to get my hands on one of these beautiful and incredibly well built PowerMac G5 cases and do a Hackintosh conversion but back when I got the idea they were far too expensive to risk the project on, and in recent years I was just too busy. Updated picture here: Let's take a look at the finished product! The kit mounts in the same way as the G5 kit using shelf mountings and lower case mountings to fix the tray in place inside the Mac Pro casing. This is not a tutorial, just a tour of the completed project. But those kits didn’t made the Apple Power Mac G5 watercooling-ready. Those kits let you mount an ATX mainboard and use the back IOs. Most of them used professionally made, lasercut conversion kits available for around 100 €. A few people bought old Apple Power Mac G5 cases and changed them internally to fit ATX mainboards. The original paint job was a chipped black gloss with some sort of red primer. G5 ATX kit with PSU holder G5 full ATX 120 and Original version kits G5 mATX 120 kit G5 mATX Original kit Motherboard Tray Mac Pro Kits Powermac G4 Conversion Products Powermac G5 conversion products Front Panel Conversion for G5/Mac Pro Refurbished Macs Motherboard Trays Cube G4 trim sheet The junkyard.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |